How does a heat pump work?
A heat pump moves heat from one place to another rather than burning fuel to create it. The process works the same way as a refrigerator, just in reverse. A refrigerant fluid circulates through the system, absorbing heat from outside air or the ground. The refrigerant evaporates as it absorbs this heat, then passes through a compressor which raises its temperature significantly. The concentrated heat is then transferred through a heat exchanger into your central heating system and hot water cylinder, and the refrigerant returns to liquid form to start the cycle again.
Because a heat pump moves existing heat rather than generating new heat, it produces three to four units of heat for every one unit of electricity it consumes. This ratio is called the Coefficient of Performance, or COP, and it is why heat pumps are significantly cheaper to run than direct electric heating and increasingly competitive with gas as UK electricity prices shift relative to gas.
Modern air source heat pumps use refrigerants with very low Global Warming Potential. Many current models, including newer units from Vaillant and Samsung, now use R290 (propane) as the refrigerant, which has a GWP of just 3 compared to older refrigerants that had GWP values in the thousands. This makes modern heat pumps significantly better for the environment across their full lifecycle, not just at the point of operation.
Heat pumps work best when delivering heat at lower flow temperatures, typically between 35 and 45 degrees Celsius, compared to the 65 to 70 degrees a gas boiler usually runs at. This makes them most effective when paired with underfloor heating or with oversized low-temperature radiators. Every 5 degrees you can reduce the flow temperature improves efficiency by around 10 per cent.
What types of heat pump are available in the UK?
There are three main types of heat pump relevant to UK domestic installations: air source, ground source, and hybrid systems. Within air source there are two main configurations: monobloc and split.
Air source heat pumps
Air source heat pumps extract heat from outside air and are by far the most widely installed type in the UK. They are the practical choice for most domestic properties because they require no groundworks, can typically be installed in one to two days by an MCS-accredited engineer, and qualify for the Boiler Upgrade Scheme grant. Modern units work effectively at outdoor temperatures as low as minus 15 to minus 20 degrees, covering the full range of UK winter conditions.
A monobloc air source heat pump houses all components including the compressor, heat exchanger, fan, and refrigerant circuit in a single outdoor unit. Water pipes carry heat into the property and connect to the central heating system and cylinder. Monobloc systems are the standard configuration for UK domestic installations because they are straightforward to install and do not require F-gas certified engineers to work on refrigerant pipework inside the property.
A split system divides the heat pump into a separate outdoor unit and an indoor unit connected by refrigerant pipework running through the building. Split systems can offer installation flexibility in certain property types but require F-gas certified engineers for commissioning and are less commonly specified for standard UK domestic retrofits.
At MP Moran we stock two of the most specified monobloc air source heat pump ranges in the UK trade. The Vaillant arotherm+ is available in 3.5kW, 5kW, 7kW, 10kW, 12kW, and 15kW outputs. It uses R32 refrigerant, achieves A+++ ErP efficiency ratings, operates down to minus 20 degrees outside, and integrates with Vaillant uniSTOR cylinders and the myVAILLANT smart controls platform. The Vaillant arotherm+ 7kW achieves a seasonal COP of around 3.8 to 4.0 at A7/W35 test conditions. The Samsung monobloc is available in 8kW, 12kW, and 16kW and comes as a pre-plumbed bundle with a Joule Kodiak unvented cylinder in 170, 210, 250, or 300 litre capacities, reducing installation time on site significantly. Both ranges are MCS listed and BUS grant eligible.
Ground source heat pumps
Ground source heat pumps extract heat through buried pipework, either as horizontal loops in trenches or as vertical boreholes drilled to depths of 50 to 200 metres. Because ground temperature in the UK stays relatively stable at around 10 to 12 degrees year-round, ground source systems can achieve slightly higher efficiency than air source in very cold weather. However, installation costs are significantly higher, typically starting at £15,000 to £20,000 and rising to £30,000 or more depending on borehole depth and ground conditions. They require substantial outdoor space and specialist contractors, making them impractical for most urban and suburban properties.
Hybrid heat pump systems
A hybrid system pairs an air source heat pump with an existing gas or oil boiler. The heat pump handles the base heating load on mild days, when it operates most efficiently, while the boiler provides backup on the coldest days or for peak demand. Hybrid systems can be a practical transitional option for properties where a full heat pump retrofit is not yet possible due to insulation levels or radiator sizing. Since November 2025, the Boiler Upgrade Scheme has also been expanded to include air-to-air heat pumps, giving more installation types access to government support.
What changed in 2025: new rules every homeowner needs to know
2025 brought the most significant changes to heat pump regulations in the UK for many years. If you are researching a heat pump installation, these changes are directly relevant to what you can install, where, and what is required.
Permitted development rights updated from May 2025. From 20 May 2025, new permitted development rules came into force in England that make installation simpler and more flexible. The old one metre boundary rule, which required every heat pump to be placed at least one metre from the property boundary, has been removed. Heat pump units can now be positioned closer to fences, walls, and boundaries, which significantly helps properties with constrained outdoor space. Separately, detached homes can now install up to two air source heat pump units under permitted development rights, supporting cascade configurations where two smaller units work together to meet the heating demand of a larger property. Conservation areas and listed buildings still require planning permission.
Smart-ready requirement. All air source heat pump units installed from 2025 onwards must be smart-ready, meaning they must be capable of connecting to smart grids and adjusting operation based on energy demand or time-of-use electricity tariffs. In practice this means the heat pump can be set to run preferentially when electricity is cheapest, reducing running costs and carbon emissions. Both Vaillant arotherm+ and Samsung monobloc units are compatible with smart controls and time-of-use tariff integration.
Clean Heat Market Mechanism from April 2025. The Clean Heat Market Mechanism (CHMM) places obligations on fossil fuel boiler manufacturers to acquire credits for low-carbon heating installations. In practice this is intended to reduce the price differential between heat pumps and gas boilers over time by creating commercial incentives for the industry to support heat pump deployment.
Future Homes Standard context. New homes built from 2025 are required to produce significantly lower carbon emissions than under previous standards, with low-carbon heating systems such as heat pumps effectively mandated for new builds. This creates a long-term structural shift in demand for heat pump supply and installation that will sustain the market well beyond the current grant period.
Updated MCS certification standards. Installers working to the updated MCS 020a standard for air source heat pumps are now required to follow more rigorous commissioning and performance verification procedures. Always check that your installer is MCS certified and working to the current standard before signing a contract.
.What size heat pump do I need?
Heat pump sizing must be based on a heat loss calculation for the property, carried out to BS EN 12831. This calculation takes into account the floor area, insulation levels, window areas, thermal bridging, and the design outdoor temperature for the property's location to determine the kilowatt output required to maintain a target indoor temperature on the coldest day of the year. Getting the size right matters enormously because an oversized heat pump short-cycles, running in short bursts rather than long steady runs, which reduces seasonal efficiency and puts unnecessary mechanical stress on the compressor. An undersized unit will fall short on the coldest winter days.
As a practical guide based on typical well-insulated UK properties:
- Well insulated one to two bedroom flat or small home: 3.5kW to 5kW
- Well insulated two to three bedroom semi-detached home: 5kW to 7kW
- Three to four bedroom semi-detached home with average insulation: 7kW to 10kW
- Larger four to five bedroom detached home or older property with less insulation: 10kW to 16kW
These ranges are indicative only. The only reliable method is a proper Manual J or BS EN 12831 heat loss calculation. If your property is poorly insulated, improving the insulation before specifying the heat pump will reduce the required output, lower the unit cost, and improve running efficiency significantly. Our team at any of our six branches can help heating engineers work through the specification before quoting.
How much does a heat pump cost in the UK?
The total installed cost of an air source heat pump in the UK in 2025 and 2026 varies depending on the unit output, the brand, the complexity of the installation, and whether additional work such as cylinder replacement or radiator upgrades is required.
Unit prices for monobloc air source heat pumps from leading brands currently range from around £1,800 for a 3.5kW entry model to £4,500 or more for a 15kW to 16kW unit, before installation. Samsung monobloc units are available as pre-plumbed bundles with Joule Kodiak cylinders from MP Moran, which reduces the total system cost by combining the two main components into a single order. Installation labour in London and the South East typically ranges from £3,000 to £5,000 for a standard domestic installation, though more complex retrofits involving radiator upgrades or significant pipework modifications will cost more.
Total installed cost before the BUS grant therefore typically falls between £7,000 and £15,000 for most UK domestic properties, with the £7,500 grant reducing the net cost to between zero and £7,500 for a significant proportion of installations. For properties replacing oil or LPG heating rather than gas, the running cost savings are typically greater and the payback period shorter.
The Boiler Upgrade Scheme: how the £7,500 grant works
The Boiler Upgrade Scheme (BUS) provides a £7,500 grant towards the installed cost of an air source heat pump for eligible properties in England and Wales. The scheme has been extended to run until 2029/30, giving homeowners a long window to plan and complete an installation. Here is how it works in practice.
The property must be in England or Wales and must currently use a fossil fuel heating system (gas, oil, or LPG). The installation must be carried out by an MCS-accredited installer using an MCS-listed heat pump. The grant is applied at the point of installation: the installer claims the grant from Ofgem on the homeowner's behalf and deducts it from the invoice, so the homeowner pays the net cost only. There is no complex application process for the homeowner. MP Moran supplies the equipment and your MCS-accredited installer manages the Ofgem grant process.
Properties with an Energy Performance Certificate recommendation to add loft or cavity wall insulation must have that insulation installed before claiming the grant, or the EPC recommendation must have been reviewed and found to not be applicable. This is worth checking before proceeding with an installation.
How efficient is an air source heat pump?
Efficiency is measured as the Seasonal Coefficient of Performance, or SCOP, which averages the efficiency of the system across a full heating season rather than at a single test point. A well-installed air source heat pump in a well-insulated UK property typically achieves an SCOP of 2.5 to 4.0. The Vaillant arotherm+ 7kW achieves around 3.8 to 4.0 SCOP at standard A7/W35 test conditions. By contrast, a modern condensing gas boiler operates at around 89 to 92 per cent thermal efficiency, meaning it delivers approximately 0.9 units of heat for every unit of gas consumed.
The actual SCOP achieved on a real installation depends heavily on the flow temperature the system runs at. Running at 35 degrees flow temperature to heat an underfloor system delivers significantly better SCOP than running at 55 degrees through standard-size radiators. This is why correctly sizing the heat distribution system is as important as correctly sizing the heat pump itself. An experienced installer will carry out a heat emitter check as part of the design process to confirm whether existing radiators are adequate or whether some will need to be upgraded.
Heat pumps also degrade in efficiency as outdoor temperature falls, though modern units maintain useful COP figures even at minus 15 degrees. The Vaillant arotherm+ is rated to operate at minus 20 degrees, which covers the full range of UK winter conditions including the most extreme cold weather events.
What do I need for a complete heat pump installation?
Beyond the heat pump unit itself, a complete installation requires several components and accessories. Understanding what is needed before you buy avoids delays and additional costs on the day of installation.
A hot water cylinder is required in almost all domestic installations where the heat pump is expected to provide domestic hot water as well as space heating. Samsung monobloc bundles from MP Moran come pre-plumbed with Joule Kodiak unvented cylinders in 170, 210, 250, and 300 litre capacities. Vaillant arotherm+ units pair with Vaillant uniSTOR cylinders. The right cylinder size depends on the number of occupants and the expected daily hot water demand: 170 to 210 litres suits one to two person households, 250 to 300 litres suits three to four person households.
Installation accessories that every heat pump installation requires include a magnetic system filter rated for heat pump circuits (standard boiler filters restrict flow in heat pump systems and can void warranties), a heat pump specific inhibitor and antifreeze fluid (standard boiler inhibitors are not compatible with aluminium heat pump heat exchangers), an antifreeze valve on exposed outdoor pipework, and a flow balancing valve to set the correct circuit flow rate during commissioning. MP Moran stocks the full range of air source heat pump accessories including pipe insulation for heat pump circuits, external trunking systems, anti vibration mounts, Joule HP concentrate fluid, and Joule Robokit sealed system kits.
A sealed system kit is needed to pressurise and maintain the heating circuit. For Viessmann Vitocal 150-A installations, MP Moran stocks the full range of manufacturer-specified installation packs.
Running costs and maintenance
Running costs for an air source heat pump in the UK depend on the property's heat loss, the SCOP achieved, and the electricity tariff. Based on current UK electricity prices in 2025 and 2026, a well-installed air source heat pump in a three to four bedroom property typically costs between £600 and £1,200 per year to run for space heating and hot water combined. This compares to gas boiler running costs of £800 to £1,500 for a similar property, depending on gas tariff. Properties switching from oil or LPG heating typically see greater savings.
Registering for a time-of-use electricity tariff, such as Octopus Flux or a similar smart tariff, can reduce running costs further by running the heat pump preferentially during off-peak hours when electricity is cheaper. The smart-ready requirement for all 2025 installations means new heat pumps are designed to integrate with these tariff structures from day one.
Air source heat pumps require annual servicing to maintain the manufacturer warranty and keep the system running efficiently. A typical annual service check covers refrigerant pressure, electrical connections, filter condition, system pressure, and controls calibration. Service costs vary but typically fall between £100 and £200 per year for a domestic system. Heat pump compressors have an expected lifespan of 15 to 20 years with regular maintenance, making the long-term cost of ownership competitive with a gas boiler replacement cycle.
Is a heat pump right for my home?
An air source heat pump works well in most UK properties that meet a few conditions. Good insulation is the single most important factor: a draughty property loses heat faster than a low-flow-temperature system can replace it efficiently. Improving insulation before installation reduces the required heat pump output, improves SCOP, and lowers running costs. The property needs outdoor space for the unit, typically a clear wall or ground area of roughly one metre by one metre, though the removal of the one metre boundary rule from May 2025 gives much more flexibility in positioning.
Properties with existing underfloor heating are an excellent match for heat pumps and will achieve the best efficiency figures. Properties with standard radiators can still work well, but an engineer should check whether the existing radiators are large enough to deliver adequate heat at lower flow temperatures. In many cases radiators do not need replacing, particularly in properties that have already been well-insulated, but this needs to be confirmed on a room-by-room basis rather than assumed.
Older properties with solid walls, poor insulation, or very high heat loss may be better suited to a high-temperature heat pump, which can deliver flow temperatures of 60 to 80 degrees and work with standard radiator systems without modification. These units are less common and more expensive, but they are an option worth exploring for harder-to-retrofit properties where the cost of upgrading insulation and radiators would be prohibitive.
If a full heat pump installation is not the right move yet, a hybrid system running an air source heat pump alongside the existing boiler reduces gas consumption and carbon emissions immediately while allowing time for insulation and radiator upgrades to be planned and completed in stages.
Where can I buy a heat pump in the UK?
MP Moran supplies air source heat pumps from Vaillant and Samsung to heating engineers, contractors, and homeowners across London and Hertfordshire. We are a family-owned, independent builders and plumbers merchant that has been trading since 1976. Our team can help you specify the right unit, cylinder, and accessories for your project before you order, and we can talk through the technical requirements of a specific installation if you are unsure about sizing, controls, or accessory selection. Unlike a national distribution warehouse, when you call one of our branches you speak to someone who understands heat pump specifications and can give you a straight answer.
Browse our air source heat pumps range including the full Vaillant arotherm+ and Samsung monobloc line-up. Explore the complete heat pumps category for all types, or visit our heat pump accessories page for everything needed to complete the installation correctly. Heat pump units are delivered direct to your site or home address. Accessories are available for Click and Collect from our six branches in Watford, Kilburn, Willesden, West Hampstead, Kennington, and Tottenham, or delivered direct to site. Not yet a trade account holder? Sign up online to access trade pricing across our full range.
Heat Pumps FAQs
What is a heat pump and how does it work?
+
A heat pump is a heating system that transfers heat from an external source — typically the outside air or the ground — into your home, rather than generating heat by burning fuel. It works using the same refrigerant cycle as a fridge or air conditioning unit, compressing and expanding refrigerant gas to extract thermal energy from even cold outdoor air and move it indoors. For every unit of electricity the system consumes, a well-designed heat pump typically delivers three to four units of heat in return, making it significantly more efficient than a conventional boiler. Air source heat pumps are the most widely installed type in the UK and sit outside the property as a compact fan unit. Ground source heat pumps draw heat from pipes buried in the ground and offer higher efficiency but require more space and a larger upfront investment. Both types can provide space heating and domestic hot water for most UK homes.
What is the difference between an air source and a ground source heat pump?
+
Air source heat pumps extract thermal energy from outdoor air and are by far the most commonly installed type in the UK, accounting for around 99% of retrofit installations. They require only a small external unit and are straightforward to install on most properties. Ground source heat pumps use a network of pipes buried in the garden or drilled vertically into the ground to extract heat from the earth, which maintains a more stable temperature year-round than the air. This makes ground source systems slightly more efficient, but they cost significantly more to install — typically £28,000 to £34,000 compared to £10,000 to £15,000 for an air source unit — and require sufficient outdoor land area. For most urban and suburban UK homes, an air source heat pump is the practical and cost-effective choice. Ground source systems are better suited to rural properties with large gardens or land.
How much does it cost to install a heat pump in the UK?
+
Air source heat pump installations in the UK typically cost between £10,000 and £15,000, including the unit, labour, and associated plumbing work such as a new hot water cylinder. Ground source heat pumps are considerably more expensive, generally ranging from £28,000 to £34,000 depending on whether a horizontal ground array or vertical borehole is required. These figures can be reduced significantly through the Boiler Upgrade Scheme (BUS), which offers a £7,500 grant towards eligible installations in England and Wales, and similar support is available in Scotland through the Home Energy Scotland scheme. Some mortgage providers also offer cashback of up to £2,000 for heat pump installations through approved schemes. The final cost will depend on property size, existing heating infrastructure, whether radiator upgrades are needed, and local installer rates. Always get at least three quotes from MCS-certified installers before committing.
Is my home suitable for a heat pump?
+
Most UK homes are suitable for a heat pump, though the system performs best in well-insulated properties where heat loss through walls, windows, and the roof is minimised. Good insulation allows the heat pump to operate at lower flow temperatures, which is where it delivers the greatest efficiency. Homes with cavity wall insulation, loft insulation, and double glazing are well placed for a straightforward installation. Older or solid-wall properties may benefit from insulation improvements before installation to get the most from the system. You will also need a small amount of outdoor space for an air source unit — typically a flat, firm surface with good airflow around it — and a hot water cylinder if your existing setup is a combi boiler. A qualified MCS-certified installer will carry out a heat loss survey before specifying the right system for your home.
Can a heat pump replace a gas boiler completely?
+
Yes, a correctly sized heat pump can replace a gas boiler entirely, providing both space heating and domestic hot water for the whole property. Unlike a combi boiler, a heat pump requires a hot water cylinder to store heated water, so this will need to be factored into the installation if your current system is combi-based. Some homeowners opt for a hybrid heating system during the transition, which combines a heat pump with the existing boiler — the boiler provides backup on extremely cold days or when peak demand is high, while the heat pump handles the majority of the heating load. A full replacement with a heat pump is the more carbon-efficient long-term solution, particularly as the electricity grid continues to decarbonise. For properties on mains gas, the running costs of a heat pump are broadly comparable to a gas boiler at current energy prices, and the gap is expected to close as government policy shifts in favour of electrified heating.
Do heat pumps work with existing radiators?
+
Heat pumps are compatible with radiators, but they operate at lower flow temperatures — typically 35 to 55°C — compared to the 60 to 75°C delivered by a conventional gas boiler. This means existing radiators need to be large enough to emit sufficient heat at those lower temperatures. In many properties, particularly those built in the last 20 years where radiators tend to be oversized relative to the boiler output, the existing radiators will work without replacement. Older properties with smaller single-panel radiators may require some or all of them to be upgraded to larger double-panel or low-temperature models to maintain comfort levels. Underfloor heating is an ideal distribution system for heat pumps due to its large surface area and low flow temperature requirements. A heat loss survey carried out by a qualified installer will identify whether radiator upgrades are needed before the heat pump is specified.
How efficient are heat pumps?
+
Heat pump efficiency is measured by the Coefficient of Performance (COP), which expresses how many units of heat are produced for each unit of electricity consumed. A well-designed and properly installed system typically achieves a COP of 3 to 4, meaning it delivers three to four times more energy as heat than it uses in electricity. The Seasonal Coefficient of Performance (SCOP) measures average efficiency across the whole heating season and is a more useful real-world figure. Best-practice installations with correctly sized radiators and good insulation can achieve SCOP values of 4.5 or higher, while the UK average is closer to 3.0 due to variation in installation quality. Heat pump efficiency drops slightly as outdoor temperatures fall, but modern units continue to operate effectively well below 0°C, which is rarely a problem in UK conditions. Properly sizing the system and keeping flow temperatures as low as possible are the two most important factors in achieving peak efficiency.
Are heat pumps cheaper to run than a gas boiler?
+
At current UK energy prices, running costs for a heat pump are broadly comparable to a gas boiler for an average home, with government modelling suggesting a saving of around £100 per year for a typical property switching from gas. The comparison depends heavily on your electricity and gas tariff, the efficiency of your installation, and the insulation level of your home. For properties currently heated by oil or LPG, the savings are more significant, as heat pumps are typically far cheaper to run than either fuel type. Smart electricity tariffs, which offer cheaper overnight rates, can improve heat pump running costs further, particularly if you can pre-heat your home or hot water cylinder during off-peak hours. As the electricity grid decarbonises and policy moves to rebalance the electricity-to-gas price ratio, heat pumps are expected to become increasingly cost-competitive with gas. Over the full lifecycle — typically 15 to 20 years — heat pumps represent strong value against fossil fuel alternatives.
Do heat pumps work in cold weather?
+
Yes, modern heat pumps work effectively in cold weather and are designed to operate in outdoor temperatures well below 0°C. Most units continue to deliver reliable heating down to around -15°C to -20°C, which is far below anything typically experienced in the UK. Efficiency does reduce slightly as temperatures fall — the greater the difference between the outdoor temperature and the target indoor temperature, the more electricity the system uses — but this rarely causes comfort issues in UK conditions. In very cold spells, some systems include a backup immersion heater or supplementary electric element to maintain performance. Given that the UK climate rarely drops below -5°C even in winter, cold weather performance is not a significant practical concern for most UK homeowners. Correct sizing by the installer ensures the system is specified to handle the full range of temperatures your property will encounter.
What grants are available for heat pumps in the UK?
+
The main government grant available in England and Wales is the Boiler Upgrade Scheme (BUS), which provides £7,500 towards the installation of an eligible heat pump in homes and small businesses. The installation must be carried out by an MCS-certified installer, who will apply for the voucher on your behalf. In Scotland, the Home Energy Scotland Grant and Loan scheme offers grants of up to £7,500, rising to £9,000 for qualifying rural households. Applications under the BUS have grown significantly since the grant was increased in 2023, and the scheme is currently funded through to 2028 with over-allocation authorised to meet rising demand. Some banks and mortgage providers also offer cashback of up to £2,000 for heat pump installations made through approved schemes. To check current eligibility and apply, the installation must be on a property with a valid EPC that does not recommend loft or cavity wall insulation as a priority improvement.
Do I need planning permission to install a heat pump?
+
In most cases, air source heat pumps can be installed under permitted development rights without requiring a full planning application, provided the installation meets certain conditions. The unit must comply with the relevant MCS Planning Standards, and the installation must be the first heat pump fitted at the property. Recent changes to permitted development rules have removed the previous requirement for the unit to be sited at least one metre from the property boundary, and the permitted size limit has been increased. Installations on listed buildings, in conservation areas, or within certain designated landscapes may still require planning consent, so it is worth checking with your local planning authority if your property falls into any of these categories. Ground source heat pumps generally do not require planning permission for the pipe installation itself. Your MCS-certified installer will be familiar with the relevant requirements and can advise on your specific property before work begins.
How long does a heat pump last?
+
A well-maintained heat pump typically lasts between 15 and 20 years, with some systems operating reliably for 25 years or more depending on the brand, installation quality, and how the system is used. Most manufacturers require an annual service to maintain the warranty, and this yearly check is important for keeping the system running at peak efficiency and catching any minor issues before they develop. Ground source heat pumps tend to have a longer lifespan than air source units, partly because the buried pipework has no moving parts and can last 50 years or more. The compressor is the component most likely to require attention over the system's life, and replacement compressors are available for most major brands. Compared to a gas boiler, which typically needs replacing after 10 to 15 years, a heat pump's longer lifespan contributes to a lower total cost of ownership over time. Keeping filters clean and ensuring the outdoor unit has good airflow will help extend service life.
How noisy are heat pumps?
+
Modern air source heat pumps are significantly quieter than older models and comparable to the noise level of a standard air conditioning unit. The outdoor fan unit typically produces around 40 to 60 decibels at one metre distance — broadly equivalent to moderate rainfall or a quiet conversation. At typical garden distances, this is unlikely to cause any disturbance. The internal components of the system operate at around 18 to 30 decibels, which is barely audible. Siting the unit thoughtfully — away from bedroom windows and not directly against a boundary wall — is good practice and will minimise any potential nuisance to neighbours. The MCS Planning Standards specify noise limits that all certified installations must meet, and your installer will confirm compliance as part of the design process. Hybrid systems that retain a gas boiler for supplementary use may also reduce the hours the heat pump fan runs, which can help in noise-sensitive locations.
Can a heat pump also cool my home in summer?
+
Many heat pumps are reversible and can provide active cooling in summer by reversing the refrigerant cycle to extract heat from inside the home and transfer it outdoors — operating on the same principle as an air conditioning unit. Air-to-air heat pumps deliver cooling directly into the room and are particularly effective for this purpose. Air-to-water heat pumps, which connect to a wet central heating system, can also provide passive cooling by circulating cooled water through underfloor heating circuits or fan coil units, though this is less common in standard UK residential installations. The UK government's Warm Homes Plan has moved to support the rollout of air-to-air heat pumps that provide a combined heating and cooling function, recognising their value as summer temperatures in the UK continue to rise. If summer cooling is a priority, discuss this requirement with your installer at the design stage so the correct system type is selected.
What maintenance does a heat pump need?
+
Heat pumps require less maintenance than a gas boiler but do need an annual service to keep them running efficiently and to maintain the manufacturer warranty. The yearly service typically covers checking refrigerant levels, inspecting electrical connections, testing controls and sensors, cleaning filters, and verifying that the system is operating within designed parameters. Between services, the main homeowner tasks are keeping the outdoor unit clear of debris, leaves, and snow, and ensuring adequate airflow around the fan. The indoor hot water cylinder and associated controls should also be checked periodically. If you are receiving support through the Boiler Upgrade Scheme, keeping your heat pump in good working order and serviced in line with manufacturer requirements is a condition of the grant. Most heat pump manufacturers and installers offer annual service plans, which provide peace of mind and protect your investment over the full life of the system.
